|
|
|
|
|
|
|||||||
| Drag Racing Discuss Drag Racing here be it dirt or tarmac. Sponsored by Sydney Dragway. |
 |
|
|
Thread Tools | Display Modes |
21-04-2012, 01:15 PM
|
#1 | ||
|
Regular Member
Join Date: Jul 2011
Posts: 116
|
Hello Everyone,
I have a TC Cortina with a Clevo. The motor should be a low 300hp and should run mid 12's. They are light in the rear and the car is untubbed. The Engine builder has recommended that I run a 26" x 8.5 slick. General opinion is that I should run the MT Street ET as oppossed to a full slick. Problem is, I can't get a 26 x 8.5 MT. I can get 24" which is no good for my combo or a 26"x 9.5 which is too wide for the car. Does anyone have any suggestions. The alternative is that I just go to a full slick and, as I understand I'll have to run front runners which is something I didn't want to do, one, for the extra cost and two, for the unwated attention on the street.The car currently is running radials at the front. Any help will be appreciated. Cheers. |
||
|
|
|
22-04-2012, 08:45 AM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2010
Location: NQ
Posts: 1,781
|
If you get a full slick you can use light truck tyres (cross ply or rags) for the front and have them on a spare set of factory rims so you can change after racing. Otherwise it looks like you would have to pump the guards to get the et streets under there, either way you look at it, there is going to be some extra cost that will have to be allowed for. Before you do anything I would take it for a run and see how bad the wheel spin is and what time you run.
|
||
|
|
|
|
22-04-2012, 09:55 AM
|
#3 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2009
Posts: 905
|
What rear gears are you running ?
How wide can you fit under the back now ? What size rims do you have ?
__________________
1998 AU VCT Ghia - Stock as a rock - Wifes car 1991 Toyota Soarer TT - 11.72 @ 116.7mph 2004 Ford Escape XLT V6 - Family Ride . |
||
|
|
|
|
22-04-2012, 02:07 PM
|
#4 | ||
|
Regular Member
Join Date: Jul 2011
Posts: 116
|
I'm running 3.7 gears now. I did run the car on on cheap street tyres and the car just sat on the line and was then sideways. Wheel spin was so bad I ran a 17.7 on the first run. The second run I TRIED to take off easy and ran a 15.4. The third run I ran a 16's. It definately needs slicks or MT street et.s.
I don't think I can go wider than a 8.5. Cheers. |
||
|
|
|
|
22-04-2012, 02:09 PM
|
#5 | ||
|
Regular Member
Join Date: Jul 2011
Posts: 116
|
The rims I have now are standard width EL Chaser rims.
Cheers. |
||
|
|
|
|
22-04-2012, 05:42 PM
|
#6 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2009
Posts: 905
|
Should fit235 60 15 radial under it
__________________
1998 AU VCT Ghia - Stock as a rock - Wifes car 1991 Toyota Soarer TT - 11.72 @ 116.7mph 2004 Ford Escape XLT V6 - Family Ride . |
||
|
|
|
|
22-04-2012, 08:08 PM
|
#7 | ||
|
Regular Member
Join Date: May 2010
Location: Hell
Posts: 280
|
We run 400Hp through 235/60/15 with no problem.
Ian |
||
|
|
|
|
25-04-2012, 04:04 PM
|
#8 | ||
|
FF.Com.Au Hardcore
Join Date: May 2006
Posts: 3,397
|
10.91 on 205x70x14 maxxis
http://www.fordforums.com.au/showthr...1258423&page=4 Sure the XT is heavier but making a lot more than your claimed 300hp , so a similar or greater difficulty factor.... Why don't you just go out with what you have and practice a few different techniques/tyre pressures etc , CHEAPER and a HUGE amount of satisfaction once you have got it sorted?
__________________
It's my call pizzoff, and I just called it |
||
|
|
|
|
26-04-2012, 11:55 AM
|
#9 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2008
Posts: 1,414
|
235/60-15 MT all the way
These things are unreall on street and strip |
||
|
|
|
|
26-04-2012, 06:45 PM
|
#10 | |||
|
FF.Com.Au Hardcore
Join Date: May 2006
Posts: 3,397
|
Quote:
__________________
It's my call pizzoff, and I just called it |
|||
|
|
|
|
26-04-2012, 07:01 PM
|
#11 | ||
|
Regular Member
Join Date: Jul 2011
Posts: 116
|
Thanks for the input everyone.
Cheers |
||
|
|
|
Tyres
Linear Mode
