|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-07-2011, 11:45 AM
|
#1 | ||
|
Starter Motor
Join Date: Jul 2011
Posts: 4
|
I have a 99 Cougar and the ABS red light is on all the time. Have checked the brake sensors and they are OK. Looks like I may need a new module. Took it to ford and they Self tested for codes.
Report shows "FAULT CODES LOGGED B1201-HEC+FUEL SENDER CIRCUIT FAILURE. B1318-HEC BATTERY VOLTAGE LOW." Any thoughts? I have read these modules could be in the $ thousands. Thanks Rod |
||
|
|
|
12-07-2011, 05:02 PM
|
#2 | ||
|
Regular Member
Join Date: Feb 2009
Location: Phillip Island
Posts: 374
|
theres a place in nsw that fixes these, one of the other members had this done
|
||
|
|
|
|
12-07-2011, 11:29 PM
|
#3 | ||
|
Regular Member
Join Date: Sep 2008
Posts: 70
|
I had to have mine rebuilt a few months ago, had it done by a company in Sydney. My brake mechanic removed just the module not the pump and pipes and mailed it off to the repair company. It took about 3-4 days and cost about $275 approx, a bit better than what Ford quoted ($6,600 supply only). The company are on the net so you can search or contact via:-
Specialised Automotive Elelctronics 38 Sutherland Road North Parramatta NSW 2150, Sydney Ph 0423399286 abs@autoelectronics.com.au Hope they can help you out. Trev |
||
|
|
|
|
13-07-2011, 08:45 AM
|
#4 | ||
|
Starter Motor
Join Date: Jul 2011
Posts: 4
|
Thanks Guys,
I'm in Victoria but will check the web address. They may have a partner down here. Keep you informed. Rod |
||
|
|
|
|
13-07-2011, 08:59 AM
|
#5 | ||
|
Regular Member
Join Date: Jul 2005
Posts: 455
|
I had this happen to me and the thing is that if your ABS light is ON it means it is not working. The brakes still work OK but you do not have ABS at the moment.
Apparently this is a design fault as the modules are mounted to close to the motor and the heat and vibration ultimately cause internal failiure of the circuit boards.
__________________
Owning a Cougar is like owning a Super Model Good to own but "High Maintenance"  2000 Model Eibach Cougar (Auto) - Now dead & buried 
|
||
|
|
|
|
13-07-2011, 01:41 PM
|
#6 | ||
|
Starter Motor
Join Date: Jul 2011
Posts: 4
|
Thanks for your comment arrow
Have you had yours fixed? Are the modules easy to remove? I'm led to beleive they are in an awkward postion under the dash near the brake master cylinder Rod |
||
|
|
|
|
13-07-2011, 02:53 PM
|
#7 | ||
|
Regular Member
Join Date: Jul 2005
Posts: 455
|
My "sparky" did mine and my understanding is the module is tucked up beside the motor somewhere. It is a bit bigger and thinner than a cigarette packet and is in an aluminium case. I know he bitched about what a hard job it was to get at it but then again it is always the same whenever ANYBODY has anything to do with ANYTHING under the bonnet of a cougar.
__________________
Owning a Cougar is like owning a Super Model Good to own but "High Maintenance" 2000 Model Eibach Cougar (Auto) - Now dead & buried
|
||
|
|
|
|
13-07-2011, 10:30 PM
|
#8 | ||
|
Regular Member
Join Date: Sep 2008
Posts: 70
|
What arrow has said is correct, I had to have an CV boot replaced on mine so when they disconected the axle it gave better access to the module.
|
||
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
Cougar ABS Modules
Linear Mode
